How To Sharpen Lawn Mower Blades. Lawnmower blade sharpening tool

How To Sharpen Lawn Mower Blades

sharpen, lawn, mower, blades, lawnmower, blade

One of the biggest challenges in maintaining a pristine lawn is mowing it. The warmer months mean it’s time to get each blade sharp and ready to shear those grass blades down.

Detaching your lawn mower blade will depend on your model (push mower or ride-on), but the methods for sharpening are similar. You can either clamp the blade in a vise, then file using a mill file, or work using a drill with a sharpening stone attached.

Ready for mowing season? Here’s how to sharpen lawn mower blades – after all, if you invest in the best quality lawn mower. you’re going to want to take care of it!

Why Sharpen Lawn Mower Blades?

You need to sharpen your mower blades to ensure a clean job when you cut grass. Dull blades will snag on the grass and rip it out, damaging your lawn. This will also put your lawn at risk of diseases like fungal infestation.

For the cleanest, most efficient cut while mowing, you’ll need to make sure your blades are sharp. And while you can always have the blades professionally sharpened, you can do a DIY job if you’re up to it! This is especially true if you use your mower as often as say, a professional lawn mowing service would.

Does Your Lawn Mower Blade Need Sharpening or Changing?

Here’s a tricky question – do you just need to sharpen, or should you change your lawn mower blade entirely? To answer that, check your blade at the start of mowing season. If the edge is simply dull and flat, then you only need to sharpen it. It’s the same if you notice uneven patches or tears in the grass.

On the other hand, if there are nicks or cracks in the blade, then you can’t simply sharpen it to fix it. This is the same case if there are bends or warping. In this situation, you’re better off changing the blade out to a new one.

How Often to Sharpen Mower Blades

Ideally, once every other month. But always check the blade to see if it needs sharpening. If you mow very often, it may need filing more frequently.

Things To Know Before You Sharpen Your Lawn Mower Blade

sharpen, lawn, mower, blades, lawnmower, blade

Do not aim for the sharpest blade possible – that’ll wear your blade too thin, causing it to perform inefficiently. You’ll also need to sharpen it more frequently to retain that razor-sharp edge.

Instead, aim for “butter knife sharp” so that your blade holds up longer.

Also, check what tool you’ll use to sharpen the lawnmower blades. There are two main tools you can use:

Which you use depends on your budget and what’s available to you.

Lastly, it’s not possible to sharpen a mower blade without removing it. Not only will you do an inefficient job, you might also hurt yourself in the process.

Sharpening Lawn Mower Blades

Always start by unplugging the spark plug and removing the spark plug wire. This means your mower won’t accidentally turn on and injure you while you’re working.

You should also use appropriate protective equipment, such as goggles and gloves.

Removing the mower blade

For a push mower, you’ll need to tip the mower onto its back or side. This will expose the underside of the mower, allowing you to access the retaining bolt securing the blade to the deck.

For a ride-on mower, lower the mower deck to its lowest setting so you can access the blade.

Use spray paint or a marker to note the correct orientation when reinserting the blade. The last thing you want is to install the blade upside-down – that’ll cause your mower to cut incorrectly.

How to sharpen lawn mower blades using a file

For those who don’t mow as often, or are trying to save money, the simplest tool you can use to get a sharp blade is a file.

Clamp the blade and check the angle

Insert the blade into a vise and clamp it to hold it in place. Check for the proper filing angle and move in one direction only, pushing across the top side of the cutting edge.

Take a 25cm (10in) mill bastard file and start running it along the sharp edge of the blade. Move in one direction and ensure you’re feeling the “cutting” action. Otherwise, your blade might be dull.

Use a balancer to check if the blade is properly balanced. An improperly balanced blade will cause damage to your mower in the long run.

Reinstall the blade

Reinsert the blade and tighten the main bolt. Ensure there’s no wobbling or looseness before reusing the mower.

How to sharpen lawn mower blades using a drill sharpener

sharpen, lawn, mower, blades, lawnmower, blade

There’s a heightened risk when using a drill sharpener due to the higher heat and speed involved. However, it’ll get the job done faster with less effort.

Clamp the blade and prep the drill

Again, secure the blade with a vise to prevent it from moving.

Attach the sharpening stone attachment to your drill.

Insert the cutting edge

Insert the cutting edge between the plastic guide and the stone. The guide should rest against the rear of the cutting edge.

Activate the drill and run the sharpening attachment along the correct side of the blade. Work until it’s sharpened. Then move to the other side.

It’s essential that you sharpen the same amount on each side so that the blade is balanced.

Use a blade balancer or a nail to test the balance of the blade. If one side lifts, file a bit more off the other side to even it out.

Reinstall the blade

Reinsert the blade into the deck and tighten the bolt.

Why Check a Mower Blade’s Balance?

Simple – an unbalanced blade will result in a poor cut. It’ll cause excessive vibrations and wobbling while mowing, which can damage the motor by causing undue stress. You could also cause damage to the mower deck.

Maintain Your Lawn with Sharp Lawn Mower Blades

Nobody wants a patchy lawn with ripped-up grass, so ensure you know how to sharpen lawn mower blades so they’re ready to slice through grass cleanly. This way, you can maintain a pristine lawn that you’re proud to show off to neighbours, visitors, and even yourself – no reason you can’t pat yourself on the back for your hard work!

Jamie Donovan

Jamie is an Australian horticulturalist and landscape designer. He enjoys writing about landscape architecture, garden design and lifestyle topics.

Jamie Donovan

Jamie is an Australian horticulturalist and landscape designer. He enjoys writing about landscape architecture, garden design and lifestyle topics.

How to Sharpen Lawn Mower Blades

sharpen, lawn, mower, blades, lawnmower, blade

So your lawn is starting to take off this spring, but when you finally got out there and mowed it, did that thick green grass start looking ragged and fringed with brown? A dull lawn mower blade is the likely suspect. Read on to learn how to sharpen lawn mower blades for a clean cut every time.

How to Sharpen Lawn Mower Blades in 5 Steps

Tools You Need

  • Work gloves and eye safety equipment
  • A hand metal file, angle grinder, mounted bench grinder, or dedicated lawn mower blade sharpener
  • A wrench to remove and reattach the blade
  • A wood block
  • A nail, screwdriver, or dedicated blade balancer

Prepare the Mower

sharpen, lawn, mower, blades, lawnmower, blade

NOTE: Make absolutely sure the mower can’t start by accident. Human flesh and fast blades are a terrible combination.

Gas-powered mowers: Unscrew the spark plug. Most of the time, you should be able to leave it attached via the spark plug wire. Once the spark plug is disconnected, tilt the mower on its side, making sure the air filter and carburetor are facing up. That will prevent a belch of smoke on restarting. Tighten down the gas cap.

Electric mower: disengage the cord or battery. Mark the bottom of the blade with chalk or spray paint to make sure you don’t reinstall it upside-down. Some blades are also clearly stamped “bottom” to save you this step.

Detach Mower Blades

NOTE: To sharpen the blade, first remove it from the mower. Never sharpen the blade while it’s still mounted to the mower.

In general, blades are just bolted to the deck of the mower, but the precise way they are attached can differ.

This would be a good time to head online to see if your lawn mower manufacturer has provided an online guide. Look up your mower and see if there are any quirks to detaching the blade. The guide also will likely tell you the proper size wrench to remove the nut holding the blade in place.

If the nut is stuck in too tight, try soaking it with penetrating oil or using a long-handled wrench for more torque. Wedge in the block of wood to keep the blades from turning while you loosen the nut.


sharpen, lawn, mower, blades, lawnmower, blade

Once you have the blade in hand, find the cutting edge on both sides of the blade and inspect them to see how much sharpening they need. A newer blade or one that has been kept up well could just need a few passes with the hand file or sharpening stone, but one that has been used frequently since its last sharpening may be better served by an angle grinder or bench grinder.

Follow the angle and grind on each cutting edge on each end of the blade to get a sharp edge on both sides. Dedicated lawn mower blade sharpeners make this easy, using a guide for the edges of the blades so they get the correct angle from the grinding wheel.

Oregon Products, which sells a variety of lawn-mowing products, says that a dedicated blade grinder is the best way to give a mower blade the perfect edge — sharp, but not too sharp.

“Mower blades should be aggressively sharp, but not as sharp as a razor’s edge,” the site says. “You should be able to touch the blade with your hand without getting cut.” Essentially, somewhere between butter-knife sharp and razor-sharp.

Balance the Blade

sharpen, lawn, mower, blades, lawnmower, blade

An unbalanced blade can shake the mower and potentially cause damage, so balance the blade with a few extra passes on the sharpener.

Once the blade is sharpened, make sure it’s balanced before you reattach it to the mower. This can be done by using a nail hammered into the wall of your garage or by using a screwdriver.

Place the nail or screwdriver through the blade’s center hole and see if it’s heavier on one side. If it is, give it another quick pass with the hand file or angle grinder until it’s balanced.


With your lawn mower still on its side, make sure the blade is oriented correctly, checking with the spray paint or chalk mark from Step 1. Take this chance to add some oil and lubricant to the crankshaft of the lawn mower or clean the underside of the mower deck.

Place the blade back onto the mower and tighten the hardware down to the recommended torque from your owner’s manual. Reattach the spark plug or battery and you’re ready to go.

That is, at least until those grass clippings start to look ragged and torn again.

sharpen, lawn, mower, blades, lawnmower, blade

To see whether you should sharpen your mower blade, pay attention to the lawn and how the mower is cutting. If you start to see the grass getting pulled and torn instead of cleanly cut, it’s likely time for another blade sharpening. If the blade is warped or too far gone, it may be time to purchase a new blade.

Hentschel says it only takes about a month for lawn mower blades to go dull, especially if you have seen clouds of dirt or sprays of rock shrapnel flying out from under the mower.

When to Sharpen Again

Sharpen your lawn mower’s blade at least once a year to make sure you stay on top of your lawn-care game. The frequency of resharpening depends on the level of use, but for the average person mowing a home lawn, twice a year should do the trick.

Hentschel says he’d be thrilled if folks sharpened blades at least once a year, but he recommends twice per mowing season — starting off with fresh, sharp blades in the spring and then sharpening them again around the end of June or the beginning of July to finish off the season strong.

“Once a year is way better than never,” Hentschel said.


Sharpening My Blades Isn’t Working. How Do I Know If I Need a New Mower Blade?

Here are a few indicators to look out for:

  • Significant chips or dents in the blade
  • If the blade is thinner
  • Your lawn mower blade is bent
  • The blade is still dull after sharpening

What Angle Should a Lawn Mower Blade Be Sharpened?

The most common lawn mower blade angle is 30-35 degrees. When sharpening your mower blades, it’s important to keep this 30-35 degree angle over time.

What Does a Lawn Mower Tune-Up Consist Of?

The three main components involved in a mower tune-up are the air filter, spark plugs, and oil, all of which must be changed. All you need to do is change the oil and air filter and replace the spark plug. The needed parts and supplies are available at home centers and hardware stores.

How Much Does a Lawn Mower Cost?

It depends on the size and condition of your yard as well as the type of lawn mower you want. Look at the table below to see the types of lawn mowers available and how much they cost.

Lawn Mower Type Average Cost
Reel Mower 104
Walk-Behind Mower 363
Robot Lawn Mower 1,470
Riding Lawn Mower 2,450

To dive deeper into lawn mowers and their prices, read LawnStarter’s pricing guide.

Kick Some Grass

Now that you know how to keep your blades sharp and ready to go, you’re ready to keep your grass green and neat all season long. If you’d like someone else to worry about the finer points of mowing and sharpening, contact a local lawn care pro to keep your lawn cleanly cut all season long.

Main Image Credit: isuaneye / iStockPhoto

Stuart Kushner

Stuart Kushner is a writer and aspiring product designer based in New York City. When he isn’t doing either, Stuart enjoys heavy metal music, exercise, and trying new food and drinks.

Yard work at the click of a button.

As seen in Forbes, CNBC and USA Today, LawnStarter makes it easy to schedule service with a local lawn care professional.

Enjoy your beautiful lawn.

Do you want a BEAUTIFUL LAWN?

Get easy-to-understand, actionable yard tips that will give you the greenest grass on the block.

How to Sharpen Lawn Mower Blades

When you mow your lawn with the dull blade of your lawnmower, your grass can turn brown due to the ragged cuts. For this reason, it is important to have sharp lawnmower blades. It can keep the grass healthy and green and the mow will also last longer.

All you have to do is to sharpen the blade to have clean cuts. In doing so, your lawn mowing time will be reduced and the grass can recover quickly. Here we shall explain to you how to sharpen the lawnmower blade safely.

Requirements –

The tools required for sharpening lawn mower blades are socket wrench or ratchet set, vise, bastard-cut mill file, and rags. The materials that you require will be work gloves and WD-40 lubricant.

When To Sharpen Your Mower Blade?

When you cut the grass, the nutrients will return to the lawn so that there will be strong and green-looking grass. For this, it is important to provide clean cuts. You can offer a clean cut with a sharp mower. However, with regular use, the lawnmower blade can become blunt and dull. It is important that you inspect the blades from time to time.

  • When there are worn-out blades, you will have to remove them and hone the edges.
  • It is advisable to sharpen the mower blade at least twice a season.
  • Some people often tend to sharpen the blades after 25 hours of use.
  • You will also have to sharpen them when the blades hit rocks which can cause dents.
  • At times you will find it difficult while mowing, where the lawn will give you hints that the blades are dull.
  • You have to look out for different signs like uneven grass height, dents or nicks, torn-looking blades, or frayed grass edges.

Removing and Cleaning Blade

To sharpen the blade, you will have to safely remove the blade from the lawnmower. It is always advisable that you disconnect the power source or battery. Always disconnect the spark plug wires. It helps to protect from any kind of shocks due to power. You can do it in the following way:

  • For better safety, you can wear protective eye gear and gloves.
  • Firstly, always drain the gas tank which will help to prevent fuel spills. You need to turn the mower on its side carefully. However, make sure that the carburetor and air filter are on the upward-facing side.
  • Use a permanent marker or a grease pencil to mark the bottom of the blade. In doing so, you will be able to install it right side up after sharpening the blade.
  • Now you will have to look out for the nuts. By using a wrench or a socket, you can easily loosen the nuts to release the mower blade. Apply more leverage if the grip is very tight. You need to clamp the blade and brace it with a piece of scrap wood.
  • If in any case the threaded shaft and nuts are stuck together, you will have to apply penetrating oil. Always allow it to sit in for a couple of hours.
  • Before sharpening, you will always have to clean the blade with a microfiber cloth or a dry rag. At times you may find the blade to be covered in grass clippings where you will have to use penetrating oil. Allow it to sit for some time and then scrub the debris with a stiff brush.

How To Sharpen Lawn Mower Blade?

To prepare for cleaning, you will have to gather the tools. You will first have to confirm if the blade is damaged or dull. Keep in mind the opposite sides of the blade have a cutting edge of up to 4 inches. To examine the blade, you will have to clamp the mower blade onto a worktable. Keep the cutting edge facing upwards. Look carefully for the signs if it requires sharpening or replacement. A replacement has to be done if the blade has cracks or if it is severely bent. If the blade is dull or chipped, you will have to sharpen it.

The lawnmower blade sharpening can be done in multiple ways. To sharpen it with the hand you will require abrasives or metal files. If you are looking to sharpen it with a machine, you will require a bench grinder, angle grinder, or blade sharpener.

While sharpening you will have to do it safely so that it will not cut your finger. If it is a razor-sharp blade, the likelihood of becoming dull is even more. It is advisable to go for replacement rather than have constant sharpening.

Sharpening by Hand

Always begin by wearing protective gloves and eye gear. You will have to protect yourself from metal shavings and sparks.

  • Use a grindstone or a file of 10 inches to sharpen the blade’s edge. You need to keep the file approximately about 45 degrees.
  • Begin by sharpening from the top side.
  • You will have to push the file in one direction without sawing back and forth.
  • While filling, you will be able to feel the file teeth. When there is no such feeling, you will have to apply a little pressure.
  • Try to reach rough spots and follow the blade edge’s angle. Do note that most blades require sharpening in less than 50 file strokes.
  • After finishing one edge, you will have to release it from the vise.
  • Repeat the process by turning it over to the other side.

Sharpening with Blade Sharpener

Here also you will have to put on gloves as well as hearing protection.

  • You will have to begin by clamping the blade into a vise.
  • Take a standard drill and insert the blade sharpener into it. The blade sharpener comes with a grinding stone that has a beveled edge. It also features a shank of 0.25-inch and a guide piece.
  • Begin by pulling the drill trigger to start it.
  • You can now place the grinder on the mower blade. To have the right sharpening angle, you must keep the flat guide against the blade rear. Also, the cutting edge must slot into the bevel.
  • By applying medium pressure, you will have to move the stone back and forth. Check the blade after every five strokes. It has to be free from any rough spots or nicks and must be very sharp.
  • Complete the edge and then turn the blade over. Begin the process and sharpen the other edge.

When you happen to use a power sharpener, never overheat the blade’s edge. If it is ho,t you can dunk it in a bucket of water.

Sharpening with Angle Grinder

To begin with, you will always have to wear safety gear like ear and eye protection and work gloves.

  • Clamp the blade by using a vise. For the angle grinder, you can use a flap disc.
  • It is advisable to align the mower blade cutting edge with the grinder’s blade.
  • You need to move the grinder slowly against the edge of the blade.
  • Try to do it on the existing edge and make sure there are no rough spots.
  • After completing one edge, you can repeat it by turning it over.

If you feel that the sharpening is complete, you can always check it. Get a piece of paper or a blade of grass and it must cut easily.

Check Blade Balance

Before you install the blade, it is important to confirm the blade balance. An unbalanced blade can lead to vibrations that can damage its components. A well-balanced blade will have smooth running. Any imbalance can even damage your mower and you will have to look for a replacement. There are even ways to check the blade balance by using a blade balancer. You can confirm it in the following way:

  • You can begin by supporting the blade like a scale and using a screwdriver. Now insert the tip of the screwdriver in the blade’s hole. You will find that the blade will balance or drop on the handle.
  • Holding the blade horizontally, you must let it go. In this process, keep in mind that it should remain level.
  • The primary sign of an unbalanced blade is that the blade drops at one side.
  • It can even happen that the depth side is heavier. You will have to remove some metal by taking off a few strokes.

Reinstall the Blade

Reinstalling the blade is a key factor in determining the overall performance. If it is under tightened, then it will make the mower hard to start. During this process, you can easily clean the bowl around the blade. Make sure that you like the area clean which is under the mower. Remove any grass clippings or mud by using a putty knife or scraper.

  • Begin by inserting the blade onto the bolt. Do note that the marked side must be upward.
  • By using a socket wrench, you can tighten the nut. It has to be secure and must be extremely tight so that the mower can start smoothly.
  • You can now connect the spark plug wire as well as the power source.
  • In the next step, you must refill the gas tank.
  • To prevent any fumes, you will have to roll the mower outside the shed or garage.
  • Finally, you can see if the mower starts smoothly.

How to Maintain Your Mower Blade?

Blade maintenance is an important thing for or perfect lawn. You will have to sharpen your blade at least twice during the mowing season. It can provide a healthy lawn and your mower will be in good shape. It does mean that you will have to keep good attention to the blades. You will have to sharpen the mower blade every time you have used it for up to 25 hours. For this, you can calculate the time you have mowed in a season. By keeping sharp blades, you don’t have to worry about getting a new one. In doing so, your blade can last longer.


We have discussed how often should you sharpen your blades. It is very important to sharpen the mower blade. Sharp blades offer clean mowing and can save you money. It can last very long when there is proper maintenance. You will have to look for any signs which can actually compromise the performance of the mower. However, you must maintain safety while sharpening the mower blade and do it carefully.

One Response

Hi, I really liked the articles on sharpening lawn mower blades. But I have come up with a question. I have a lean mower with two blades. So when I put them back on how do they need to go back on? I mean like should they be placed like this – – or || or — l. Not sure how to explain it. Do the blades both face like on a clock 9 to 3 or do I place on blade at 9to3 the other at 12to6? I hope you can understand what I’m trying to ask. Thanks Mark

The LawnmowerBlade that “cuts itself sharp

Any landscaping professional knows that sharper mower blades make for sharper-looking lawns, but blades that maintain their sharpness can also improve a lawn-care business’s on-site efficiency and cut its maintenance costs.

Mowing lawns with LaserEdge Eversharp blades means minimal maintenance and downtime associated with blade sharpening, increasing overall uptime and profits.

sharpen, lawn, mower, blades, lawnmower, blade

Redefining the Cutting Edge

High-quality, hardened steel blades equipped with the LaserEdge Eversharp technology on their cutting edges have demonstrated their toughness and durability in field tests, even in the most abrasive conditions.

In one test, the LaserEdge Eversharp cutting edge withstood 30 hours in severe sand conditions and became sharper during use. In a highly controlled durability test, the blade’s advanced technology performed remarkably, enduring multiple impacts from a 1-inch steel stake traveling at more than 200 mph.

Hours of Toughness

In an intense 50-hour field test in central Florida, mower blades with LaserEdge Eversharp technology proved they “cut themselves sharp” when a new cutting edge emerged as the blade wore down.

In the test, a brand-new mower blade had LaserEdge technology applied on one cutting edge and was left untreated on the other edge. After putting the blade to work for 50 hours, the results were clear. The LaserEdge cutting edge was still sharp, and the untreated side was dulled and worn away.

Results will vary based on grass type, soil type and condition, and geographical region.

sharpen, lawn, mower, blades, lawnmower, blade

Cutting Costs, Boosting Bottom Lines

Increased Fuel Efficiency

Dull blades produce resistance, putting strain on the mower deck and making it difficult to maintain speed and efficiency. Mowing with a dull blade can reduce fuel economy by as much as 22 percent, which increases operating costs and reduces productivity.

Healthier, Greener Lawns

A dull blade shreds and tears grass, leaving it vulnerable to dehydration, browning, and disease. LaserEdge blades cut grass cleanly, making it easier to deliver high-quality lawn care and in-demand enhancements such as lawn striping.

Blades Stay Sharp Longer

In abrasive conditions, a blade can get dull in as little as four hours, and lawn-care operations can go through dozens of blades a week, resulting in downtime and lost revenue. No matter the environment, a LaserEdge blade “cuts itself sharp,” reducing time spent sharpening.

Less Mower Maintenance

Blade replacement can be a dangerous undertaking. Attacking a dulled edge with a makeshift sharpening tool can irreversibly damage a blade and put workers in danger. LaserEdge blades dramatically reduce the frequency and risk of blade sharpening.

D.H. Steinegger, R.C. Shearman, T.P. Riordan and E.J. Kinbacher, “Mower Blade Sharpness Effects on Turf,” in Agronomy Journal 75 (1983): 479–480.

Savings Calculator

See how much you can save with LaserEdge Eversharp lawnmower blades.

  • 432 Saved on Fuel Cost
  • 1575 Saved on Blade Sharpenings
  • 2625 Additional Revenue Opportunity
  • ( 960 ) Premium Spent on LaserEdge Blades

Calculations above are based off the following: type of lawn mower: 3-blade, 60-inch cut, gas-powered. Average gas price: 2.38. Lawn mower blade pricing: standard blade is 16. Average cost of sharpening: 5 per blade. Fuel savings: 11%. Blade removal and re-installation time: 30 minutes.

Frequently Asked Questions

How does LaserEdge Eversharp maintain a cutting edge that “cuts itself sharp”?

The LaserEdge Eversharp technology is applied to the underside of the cutting edge. As the blade cuts grass, the original blade material begins to wear away and exposes a new LaserEdge cutting edge, which is even sharper than the blade’s original sharpness.

Will I need to sharpen my LaserEdge Eversharp lawnmower blades?

LaserEdge blades “cut themselves sharp” and require minimal sharpening, but you should monitor cutting-edge wear. Sharpening is only needed if the new LaserEdge cutting edge is not presenting itself.

If I find the need to sharpen my LaserEdge Eversharp mower blades, how do I do so?

If you choose to re-sharpen your LaserEdge blade, do so in a safe, controlled setting with the proper equipment. Remember to prep the machine and remove the spark plug before removing the blade. Secure the blade to a work surface with a vise or clamp, and sharpen the blade with a file, bench grinder, or professional blade grinder. Ensure the blade is evenly sharpened and balanced before remounting on the mower deck.

How often will I need to change my LaserEdge Eversharp lawnmower blades?

The LaserEdge blade is designed to “cut itself sharp” and requires minimal sharpening over its life. The overall life of the blade will vary due to conditions, but its lifespan should be at least as long as a standard blade’s. In several of our tests, we found LaserEdge blades had longer lives.

How do LaserEdge Eversharp lawn mower blades perform in abusive mowing conditions?

The LaserEdge technology is an extremely hard, wear-resistant material. If you mow in conditions that regularly include rocks, curbs, out-cropping stones, and other hard objects, LaserEdge lawn mower blades may not be suitable for your operation.

A good test to see if LaserEdge is right for your operation is to inspect your worn blades. Worn blades that show excessive gouging, deep gashes, or large scraps may not see all the benefits of LaserEdge.

How long will it take for LaserEdge Eversharp to take effect?

This is highly dependent on geography, soil type, and cutting conditions. The magic of LaserEdge happens when the base blade material wears away at a faster rate than the harder, more wear-resistant LaserEdge material. In highly abrasive soil conditions (like sand), we have experienced standard blades wearing out in as few as 50 hours with blade sharpenings occurring as frequently as every 4 to 8 hours. In these areas, LaserEdge began exhibiting self-sharpening in as little as 5 to 10 hours. When using LaserEdge, these blades required no sharpening over the entire life of the blade. In less abrasive conditions, LaserEdge technology will take effect but over a longer time period.

How much do LaserEdge Eversharp lawn mower blades cost?

The price of LaserEdge blades will vary depending on the OEM and blade configuration. Although the LaserEdge will typically be more expensive than a standard blade, the benefits of consistently having a sharp cutting edge and increased uptime surpass the increase in blade price (see Savings Calculator).

Where can I purchase LaserEdge Eversharp lawnmower blades?

Most lawn mower Original Equipment Manufacturers (OEMs) are currently in the process of adding LaserEdge to their product line-ups. Be sure to talk to your local dealer about LaserEdge.

How do I get more information on LaserEdge Eversharp blades?

Fill out the contact form at the bottom of this page, and Fisher Barton will email you updates on product availability and news.

Get LaserEdge For Your Business

Ready to bring this cost-effective, state-of-the-art mower blade technology to your lawn-care business? LaserEdge blades are currently available through select OEMs.

Available for the following brands through their independent dealers: (Click on the logo for information on available part numbers)

Connect With An Expert

We’re here to help and would love the opportunity to discuss your technical questions or application challenges.

| Denial of responsibility | Contacts |RSS | DE | EN | CZ